Helo DSL Report Gurus,
I recently moved (sold my soul) from TekSavvy 150 to Rogers 1Gbps/30mbps for a deal I could not pass up.
However using the same coaxial outlet that my TSI modem was in I am only getting speeds of 200-290mbps down and a solid 33 up.
I am seeking advice on how I can improve my speeds. I have a feeling it may be one of the following factors:
-I live in rowhouses/townhouses but based off the wifi names its 80% bell users.
-The coax port comes 'from' the wall, its not a faceplate this leads me to believe someone may have pulled it and I am unaware if this is the shortest run or not. All the other coax that is on a wall plate does not work with the modem.
My setup is as follows:
Coax > CODA-4582U > Cat6 (50ft) > WatchGuard T10 > Cat5 (2ft) > Cisco SG-300 > Devices
Speeds are 200-290mbps
Tested as well:
Coax > CODA-4582U > Cat6 (3ft) > Laptop
Speeds are around 320mbps
Modem: CODA-4582U (in bridged mode)
Hardware Version 1A
Software Version 2.0.10.28T2
Modem Stats:
Downstream Overview
Port ID Frequency (MHz) Modulation Signal strength (dBmV) Channel ID Signal noise ratio (dB)
1 591000000 256QAM 4.100 7 40.366
2 855000000 256QAM -1.100 3 38.983
3 861000000 256QAM -1.600 4 38.605
4 579000000 256QAM 3.900 5 40.946
5 585000000 256QAM 3.900 6 40.366
6 849000000 256QAM 0.000 2 40.366
7 597000000 256QAM 3.700 8 40.366
8 603000000 256QAM 3.400 9 40.946
9 609000000 256QAM 4.000 10 40.946
10 615000000 256QAM 3.800 11 40.366
11 621000000 256QAM 3.800 12 40.946
12 633000000 256QAM 3.800 13 40.366
13 639000000 256QAM 3.800 14 40.366
14 645000000 256QAM 4.200 15 40.366
15 651000000 256QAM 3.700 16 40.366
16 657000000 256QAM 3.700 17 40.366
17 663000000 256QAM 4.100 18 40.946
18 669000000 256QAM 3.700 19 40.366
19 675000000 256QAM 3.400 20 40.946
20 681000000 256QAM 3.500 21 40.946
21 687000000 256QAM 3.100 22 40.366
22 693000000 256QAM 2.700 23 40.366
23 699000000 256QAM 2.700 24 40.946
24 705000000 256QAM 1.800 25 40.366
25 711000000 256QAM 1.900 26 40.366
26 717000000 256QAM 1.900 27 40.366
27 723000000 256QAM 1.500 28 40.366
28 825000000 256QAM -1.100 29 38.983
29 831000000 256QAM -1.000 30 38.605
30 837000000 256QAM -1.300 31 38.983
31 843000000 256QAM -1.500 32 38.983
32 303000000 256QAM 4.100 1 40.366
OFDM Downstream Overview
Receiver FFT type Subcarr 0 Frequency(MHz) PLC locked NCP locked MDC1 locked PLC power(dBmv)
0 4K 275600000 YES YES YES 3.900002
1 NA NA NO NO NO NA
Upstream Overview
Port ID Frequency (MHz) Modulation Signal strength (dBmV) Channel ID Bandwidth
1 38596000 ATDMA - 64QAM 34.500 3 3200000
2 30596000 ATDMA - 64QAM 31.500 1 6400000
3 23700000 ATDMA - 64QAM 31.500 2 6400000
OFDM/OFDMA Overview
Channel Index State lin Digital Att Digital Att BW (sc's*fft) Report Power Report Power1_6 FFT Size
0 DISABLED 0.5000 0.0000 0.0000 -inf -1.0000 4K
1 DISABLED 0.5000 0.0000 0.0000 -inf -1.0000 4K
I have initated a ticket with Rogers, but looking for some real advice not the comfort of their chat bot.
↧